Skip to Content

Three-Phase or Single-Phase Inverter? A Selection Guide for Installers

Choosing the right solar inverter by connection type, current, phase balance and distribution company requirements
November 16, 2026 by
Nastech Solar

Short answer: The site's grid connection determines the inverter's number of phases first. On a single-phase (L+N) connection, a single-phase inverter is the right choice; on a three-phase connection, in most cases a three-phase inverter is. As power increases, a three-phase inverter cuts the phase current to about a third and spreads generation evenly across the three phases; the exact limit is set by the connection agreement and the distribution company's requirements.

First, identify the connection type on site

The first places to look during a site survey are the meter and the main distribution board. A single-phase connection has one phase conductor, a neutral and a protective conductor (L+N+PE); a three-phase connection has three phase conductors, a neutral and PE. The same information is in the inverter's technical data: for the Jebel 10kW Single-Phase On-Grid Inverter the grid connection type is given as L+N+PE, and for the Jebel 10kW Three-Phase On-Grid Inverter as 3W+N+PE.

Note the following during the survey:

  • Connection type (single-phase / three-phase) and the power in the connection agreement
  • Main breaker rating, fuses and existing AC conductor cross-sections
  • Distribution of loads across the phases; a few days of measurements if possible
  • Grid voltage and whether the line is weak (long line, voltage rise around midday)
  • Whether a lithium battery, and thus a hybrid inverter, or EV charging will be added later

Same power, different current: choosing by power level

At the same power, a single-phase inverter carries about three times the current of a three-phase inverter. Assuming a power factor of 1, the current is I = P / U for single-phase and I = P / (√3 × U) for three-phase. At 230 V single-phase, 10 kW is about 43 A; at 400 V three-phase, about 14.5 A. The product data confirm this calculation:

ModelGrid connectionRated output current
Jebel 10kW Single-Phase On-GridL+N+PE, 230 V43.5 A
Jebel 10kW Three-Phase On-Grid3W+N+PE, 400 V14.5 A
Solis S6 10kW Three-Phase On-Grid3/N/PE, 380 V / 400 V15.2 A / 14.4 A
Solis S6 30kW Three-Phase On-Grid3/N/PE, 380 V / 400 V45.6 A / 43.3 A

As the table shows, a 30 kW three-phase inverter carries roughly the same phase current as a 10 kW single-phase inverter. High current means thicker AC cable, a larger fuse and more voltage drop on the line. On long AC lines and weak grids, inverters disconnecting from the grid because of voltage rise at the connection point are more common in single-phase systems.

The single-phase models in the catalogue range from the Solis S6 2.5kW Single-Phase On-Grid Inverter to the Solis S6 18kW Single-Phase LV Hybrid Inverter; on the three-phase side, options start at 3 kW and go up to the Solis S6 150kW Three-Phase On-Grid Inverter. However, the existence of a single-phase model does not mean that this power can be connected to every single-phase connection; that is for the distribution company to decide.

DC side: input voltage and MPPT

Three-phase inverters usually work with a higher DC input voltage, which means longer strings and fewer parallel strings. The Jebel 10kW Three-Phase On-Grid has a max. PV input voltage of 1100 V and an operating voltage range of 200–1000 V. The Jebel 10kW Single-Phase On-Grid has a max. PV input voltage of 550 V and an operating range of 80–540 V; in return, it offers 3 independent MPPTs and gives flexibility on roof surfaces facing different directions. In both cases, check that the open-circuit voltage (Voc) of the solar panels at the lowest ambient temperature does not exceed the inverter's maximum input voltage; panel voltage rises in the cold.

Phase balance: a single-phase inverter in a three-phase building

Connecting a single-phase inverter to a building with a three-phase connection is technically possible, but all the generation goes into one phase. This creates imbalance between the phases, which is the main reason why distribution companies limit the power that can be connected single-phase. If more than one single-phase inverter is used, they must be spread evenly across the phases. A single three-phase inverter, on the other hand, feeds power evenly into all three phases and is often the simpler solution.

Note one detail: a standard three-phase on-grid inverter feeds equal power into each phase. If the building's loads are unevenly distributed across the phases, one phase may be exporting to the grid while another is still drawing from it; how this affects the bill depends on the meter and the netting method. On the hybrid side, some models support unbalanced output. The Solis S6 20kW Three-Phase HV Hybrid Inverter, for example, can deliver unbalanced output of up to 40% of its rated power per phase. In businesses where single-phase loads dominate, this feature is worth considering.

Distribution company and grid rules

Choosing an inverter is not only a technical decision. In the connection application, the distribution company assesses the connection type, connection power, protection settings and, if necessary, an export limit. Confirm the exact power limits and required documents with the relevant distribution company before applying. Rules that work in the field:

  • Size the system to the power in the connection agreement; the inverter's AC power must not exceed it.
  • If there is an export limit, choose an inverter with export control. The Solis S6 5kW Single-Phase On-Grid and the Solis S6 10kW Three-Phase On-Grid Inverter support export power control; Jebel on-grid models have export limiting.
  • If the limit of a single-phase connection makes the project smaller, consider converting the connection to three-phase together with the customer.
  • Choose the AC cable cross-section and protection according to the inverter's maximum output current, not its rated current.

Quick decision table

Site situationRecommended inverter
Single-phase connection, small residential systemSingle-phase on-grid or single-phase hybrid inverter
Three-phase connection, home or small businessThree-phase inverter; spreads generation evenly across the phases
Three-phase connection, loads unbalanced across the phasesThree-phase inverter; if needed, a three-phase hybrid with unbalanced output support
Commercial and industrial roofThree-phase string inverter, many MPPTs
Battery to be added laterHybrid inverter that matches the connection type

You can find all single-phase and three-phase models in the On-Grid Inverters and Hybrid Inverters categories, and models for commercial projects on the C&I Inverters page.

Frequently Asked Questions

Can a 10 kW system be connected single-phase?

10 kW single-phase inverters exist as products; for example, the Jebel 10kW Single-Phase On-Grid Inverter has a rated output current of 43.5 A. Whether this power can be connected single-phase, however, is decided by the connection and the distribution company. Confirm before applying, and choose the cable and protection for this current.

Can a single-phase inverter be used in a three-phase building?

It can, but all the generation goes into one phase. Because of phase imbalance and the limit on connectable power, a three-phase inverter is usually the better choice in a three-phase building.

Does a three-phase inverter feed the same power into each phase?

Standard three-phase on-grid inverters do. If you need different power per phase, look at hybrid models that support unbalanced output; the Solis S6 20kW Three-Phase HV Hybrid Inverter can deliver unbalanced output of up to 40% of its rated power per phase.

Is single-phase or three-phase more efficient?

Inverter efficiency depends more on the model than on the connection type. Because the phase current is lower in three-phase, losses in the AC cable are smaller. Examples from the catalogue: the max. efficiency is given as 98.5% for the Solis S6 10kW Three-Phase On-Grid and 97.6% for the Jebel 10kW Single-Phase On-Grid.


Let's determine the right phase type and inverter power for your project together. Request a quote.

Choosing a Lithium Battery (LiFePO4): Capacity, Cycle Life and Voltage
DoD, cycle life, LV and HV, modular expansion, BMS communication and temperature