When choosing a LiFePO4 (lithium iron phosphate) battery, check five points: usable capacity (nominal kWh × depth of discharge), cycle life and test conditions, voltage class (LV 51.2 V or HV), modular expansion and BMS communication with the inverter. The temperature and IP rating of the installation location also directly affect the choice.
Below, we explain these criteria using data for the lithium batteries in our Solar Storage category from Dyness, WeCo, SolisStorage and Jebel.
Why LiFePO4?
LiFePO4 (LFP for short) is the most common lithium chemistry in solar energy storage today. The nominal voltage of an LFP cell is 3.2 V; 16 cells in series make the standard "48 V" battery of 51.2 V. The key features of this chemistry are high thermal stability, long cycle life and tolerance of deep discharge. For the same energy, it is lighter than a lead-acid battery, has a much higher usable capacity and needs no maintenance.
All the residential products we reviewed use this chemistry: the battery type of the Dyness Powerbox G2 is LiFePO4, and the cell type of the Jebel 10.24kWh battery is LFP, with a 1P8S × 2 cell arrangement, i.e. 16 cells in series.
Nominal vs. usable capacity: read the DoD
The kWh on the battery label is its nominal energy. The energy you can actually use is limited by the depth of discharge (DoD) the manufacturer recommends. For example, the Dyness Powerbox G2 10.24kWh LiFePO4 wall-mounted battery has a nominal energy of 10.24 kWh and, with a recommended DoD of 95%, a usable energy of 9.728 kWh. The WeCo 5K0-LT 5.12kWh LV LiFePO4 battery specifies a depth of discharge of up to 98%, and the SolisStorage FlexHome LV is rated at 100% DoD.
When comparing offers, go by usable kWh, not nominal kWh. The usable capacity must cover the required evening and night consumption, or the backup time needed during an outage. Also allow for the fact that, because of inverter and battery efficiencies, the energy reaching the loads from the battery will be somewhat lower than the usable capacity.
Cycle life: are the test conditions the same?
Cycle life figures can only be compared when they are measured under the same conditions. DoD, charge/discharge current (C-rate), temperature and the end-of-life criterion (EOL) change the result considerably.
- Dyness Powerbox G2: ≥8000 cycles (0.2C, 25°C, 95% DOD).
- SolisStorage FlexHome LV: > 6000 cycles (25°C, 0.2C/0.2C, 70% EOL at 100% DOD).
- Jebel 10.24kWh 48V LiFePO4 battery: > 6000 cycles (80% DOD, 25 ℃).
- WeCo 5K0-LT: > 6000 cycles (25 °C).
A value measured at 80% DoD cannot be compared directly with one measured at 95% or 100% DoD. Operating the battery on site at the recommended C-rate and at around 25°C is the most effective way to get close to the cycle life on paper.
Voltage: LV (51.2 V) or HV?
The battery's voltage class must match the inverter. LV batteries work at a nominal 51.2 V and connect to 48 V hybrid inverters; the operating voltage of the Dyness Powerbox G2 is 44.8–57.6 V, and that of the Jebel 10.24kWh battery is 46.4–57.6 V. In HV systems, the same 51.2 V modules are stacked in series to form a stack of several hundred volts. The Dyness STACK100 works at 134.4–864 V with 3–15 modules per cluster; the SolisStorage FlexHome HV ranges from 134.4–172.8 V with 3 modules to 358.4–460.8 V with 8 modules.
The rule for HV: the stack's operating voltage range must stay within the inverter's battery voltage window. That is why the minimum and maximum number of modules accepted by each HV inverter is checked separately. You will find residential batteries under Residential Energy Storage, and large HV stacks and cabinets under C&I Energy Storage in our shop.
Modular expansion
Needs can grow over time, so the expansion limit should be known from the start. Up to 50 Dyness Powerbox G2 units can be connected in parallel. The WeCo 5K0-LT expands to 15 modules in direct parallel and to 105 modules with the LV HUB accessory. The Jebel 10.24kWh battery supports up to 15 parallel connections. The SolisStorage FlexHome LV grows by adding modules from 5 to 40 kWh per unit, and up to 4 units can run in parallel.
When expanding, use modules of the same model and a compatible software version. When new modules are added next to modules that have run for years, balancing can take longer; for large additions, setting up a separate cluster is often the better option.
BMS communication and inverter compatibility
The BMS inside a lithium battery monitors cell voltages and temperatures, sets the charge and discharge current limits and shares them with the inverter. Without this closed-loop communication, the inverter cannot manage the battery correctly. The Dyness, SolisStorage and Jebel batteries we reviewed communicate over CAN and RS485; the WeCo 5K0-LT and the Jebel 10.24kWh battery also offer an RS232 interface. With Solis hybrid inverters, the SolisStorage FlexHome provides seamless on-grid/off-grid switchover in less than 10 ms.
Before commissioning, check that the battery model is on the inverter manufacturer's compatibility list, that the protocol is selected correctly in the inverter menu, and that the pin-out of the communication cable matches.
Temperature and installation location
Charging lithium batteries below 0°C can cause permanent damage inside the cells, so the BMS limits charging in the cold. The Dyness Powerbox G2 charges at 0–55°C, and down to -20°C with the optional heating function. The SolisStorage FlexHome LV charges at -20 ~ 55°C with its heating function and derates above 45°C. The operating temperature of the Jebel 10.24kWh battery is 0–55°C.
The IP rating determines the installation location: the WeCo 5K0-LT is IP20 and for indoor use only; the Jebel 10.24kWh is IP54, the Dyness Powerbox G2 IP65 and the SolisStorage FlexHome LV IP66. Mount your battery in a well-ventilated place out of direct sunlight, where the temperature stays as close to 25°C as possible.
| Model | Nominal energy | DoD | Operating voltage | IP |
|---|---|---|---|---|
| Dyness Powerbox G2 | 10.24 kWh | 95% | 44.8–57.6 V | IP65 |
| WeCo 5K0-LT | 5.12 kWh | Up to 98% | 46.5–56.8 V | IP20 |
| SolisStorage FlexHome LV | 5–40 kWh | 100% | 44.8–57.6 V | IP66 |
| Jebel 10.24kWh 48V | 10.24 kWh | — | 46.4–57.6 V | IP54 |
Lithium battery selection checklist
- Required usable capacity (kWh) and continuous charge/discharge power (kW).
- Does the voltage class match the inverter; with HV, does the number of modules fit the inverter's battery window?
- Under which DoD, C-rate, temperature and EOL condition is the cycle life stated?
- BMS communication (CAN / RS485) and the inverter compatibility list.
- Future expansion needs and the parallel connection limit.
- Installation location: indoor or outdoor, IP rating, winter and summer temperatures.
Frequently Asked Questions
Is a LiFePO4 battery the same as a lithium-ion battery?
LiFePO4 is a subtype of lithium-ion battery. It is the most widely used lithium chemistry in solar energy storage because of its thermal stability and long cycle life.
How long will a 10 kWh battery power a home?
A rough estimate is the usable capacity divided by the average load power. For example, 9.7 kWh of usable energy can in theory supply an average load of 1 kW for about 9.7 hours; with efficiency losses, around 9 hours in practice.
Can batteries of different brands be used together?
No. Only modules of the same model and a compatible software version should be used in one system; different BMSs cannot manage each other or the inverter correctly.
Can a lithium battery be installed outdoors?
Only if the IP rating and temperature range allow it. An IP65 or IP66 battery can be installed outdoors if the manufacturer permits outdoor installation; an IP20 battery is for indoor use only. Protect it from direct sun and frost.
Should I choose an LV or HV battery?
Your inverter decides: a 48 V hybrid inverter needs an LV battery, and a high-voltage hybrid inverter needs an HV battery. At higher power, HV is more efficient and easier to wire thanks to its lower current.
To choose the right lithium battery for your hybrid inverter together, request a quote.